160901_02701.jpg Edna Bay, BC - 2016 Scrubbing roof panel in the shower
| 160902_02714.jpg Edna Bay, BC - 2016 Glassing cabin bulkhead
| 160902_02716.jpg Edna Bay, BC - 2016 Glassing cabin bulkhead
|
160902_02718.jpg Edna Bay, BC - 2016 Cabin bulkhead glassed. Filler coat tomorrow.
| 160903_02722.jpg Edna Bay, BC - 2016 Testing shims - trying to fix an ugly, ragged edge
| 160903_02727.jpg Edna Bay, BC - 2016 One support a bit high
|
160904_02730.jpg Edna Bay, BC - 2016 Final sanding of roof panels
| 160906_02731.jpg Edna Bay, BC - 2016 Roof panels sanded
| 160906_02732.jpg Edna Bay, BC - 2016 For testing our skill at fill coating vertical surface
|
160907_02748.jpg Edna Bay, BC - 2016 Applying glue to roof panel
| 160907_02751.jpg Edna Bay, BC - 2016 Roof panel ready to lift into position. Blocks keep glue off the board below.
| 160907_02747.jpg Edna Bay, BC - 2016 Applying glue to roof supports
|
160907_02750.jpg Edna Bay, BC - 2016 Temporary posts will keep the panel up while we're positioning it
| 160907_02753.jpg Edna Bay, BC - 2016 Panel in place
| 160907_02757.jpg Edna Bay, BC - 2016 Screwing down panel
|
160907_02758.jpg Edna Bay, BC - 2016 Starboard roof panel glued and screwed
| 160909_02774.jpg Edna Bay, BC - 2016 Glue and screw port side roof panel
| 160909_02776.jpg Edna Bay, BC - 2016 Martha cleaning up glue squeeze out inside
|
160909_02777.jpg Edna Bay, BC - 2016 Martha cleaning up glue squeeze out outside
| 160910_02786.jpg Edna Bay, BC - 2016 Roof panels installed. The structural work is complete!
| 160910_02788.jpg Edna Bay, BC - 2016 Taping cabin roof seam
|
160910_02793.jpg Edna Bay, BC - 2016 Cabin roof taped. Fill coat later.
| 160912_02796.jpg Edna Bay, BC - 2016 Glassing gunwales
| 160913_02799.jpg Edna Bay, BC - 2016 1/2" x 1/2" x 45 degree trim. It will still need small fillets for finish.
|
160913_02800.jpg Edna Bay, BC - 2016 Installing more trim
| 160914_02803.jpg Edna Bay, BC - 2016 Trim
| 160915_02806.jpg Edna Bay, BC - 2016 Removing the cabin brow with a Fein Multimaster
|
160915_02807.jpg Edna Bay, BC - 2016 Starboard brow gone - Martha says the boat is winking
| 160915_02809.jpg Edna Bay, BC - 2016 Both brows gone. There will be trim.
| 160915_02811.jpg Edna Bay, BC - 2016 More taping of seams
|
160916_02815.jpg Edna Bay, BC - 2016 Drilling for nails
| 160916_02818.jpg Edna Bay, BC - 2016 More trim. Near the last of it. Very time consuming.
| 160916_02820.jpg Edna Bay, BC - 2016 Good joint
|
160918_02826.jpg Edna Bay, BC - 2016 Trimming back of roof
| 160918_02828.jpg Edna Bay, BC - 2016 Fine tuning. Sawdust caught by the flash.
| 160918_02837.jpg Edna Bay, BC - 2016 Trim on back edge of roof - temporarily
|
160920_02857.jpg Edna Bay, BC - 2016 Attaching roof trim temporarily
| 160920_02856.jpg Edna Bay, BC - 2016 Roof trim waiting to be glued
| 160921_02864.jpg Edna Bay, BC - 2016 Applying glue for roof trim
|
160921_02867.jpg Edna Bay, BC - 2016 Roof trim glued - forward. Screws will be replaced by doweling.
| 160921_02869.jpg Edna Bay, BC - 2016 Roof trim glued - aft
| 160928_02929.jpg Edna Bay, BC - 2016 Hydraulic steering cylinder attached to motor
|
160929_02932.jpg Edna Bay, BC - 2016 Prototype position of forward controls
| 160929_02931.jpg Edna Bay, BC - 2016 Prototype position of shift and throttle junction boxes (for dual helm controls)
|